工业烘焙连锁店
C2040SS Double-Pitch Stainless Steel Chain
C2040SS Double-Pitch Stainless Steel Chain is presented as a measured-geometry configuration for industrial bakery conveying. Use the dimensional values below for identification and RFQ preparation; final material, heat treatment, clearance, working rating and attachment details are confirmed for the ordered configuration and actual machine duty.
配置概述
C2040SS Double-Pitch Stainless Steel Chain is presented as a measured-geometry configuration for industrial bakery conveying. Use the dimensional values below for identification and RFQ preparation; final material, heat treatment, clearance, working rating and attachment details are confirmed for the ordered configuration and actual machine duty.
根据类别和安装接口的不同，该链条可用于醒发、烘焙、冷却、锅具搬运或输送等用途。替换链条时，应保持其节距、横向尺寸、链轮啮合和链架位置不变。
链条是如何构建的
输送链是由一系列铰接轴承组成，这些轴承由连接板约束。销轴和衬套构成轴承连接；滚子或衬套与链轮啮合，并在适用情况下沿轨道运行。烘焙专用输送链可能采用不锈钢结构、增加间隙、加长销轴、空心销轴或用于安装烤盘和托架的附件。
不要仅凭照片来判断链条是否可以互换。两条链条外观可能相同，但内宽、销轴长度、连接偏移量或滚子直径可能不同。这些差异会影响链轮的安装、运行轨迹和机器间隙。
尺寸参考
图纸/示意图完整显示，未进行裁剪。请将其与下表配合使用，以准备询价单。
技术规格
| 规格 | 参考值 |
|---|---|
| Pitch 25.40 mm | 确认图纸 |
| Series C2040SS | 确认图纸 |
| Double-pitch stainless construction | 确认图纸 |
此处所示数值为与此配置相关的识别尺寸。安装前请务必确认最终生产图纸，尤其是在材料、间隙、安装位置或性能等级取决于具体应用的情况下。
烘焙应用背景
在烘焙设备中，链条的负荷不仅仅取决于输送的产品。醒发系统会增加湿度和较长的循环路径；烤箱会增加热量和热运动；冷却输送机可能需要较长的输送路径；烤盘和托盘系统会增加集中的负载；包装区通常需要稳定、清洁的输送。
记录机器区域、产品输送机、链条速度、每个输送机的负载量以及清洁程序。如果链条经过区域间的过渡区域，请将该过渡区域包含在询价单 (RFQ) 中，因为温度和污染情况可能沿途发生变化。
选择和定制
几何匹配
确认螺距、内宽、滚轮/衬套直径、销轴直径、板高和总宽度。
附件匹配
确定安装孔、弯曲方向、偏移量、横杆尺寸和重复间距。
材料选择
说明材料的湿度、冲洗条件、清洁剂化学成分和温度；材料已根据这些条件进行确认。
系统检查
检查链轮、导轨、张紧装置和对准情况，以免将新链条安装到磨损或未对准的系统中。
制造与检验
尺寸检验应验证控制互换性的特征：螺距一致性、横向宽度、销轴突出长度、滚轮或衬套尺寸以及安装位置。对于定制配置，检验还应对照已批准的图纸验证载体孔位布局和安装间距。可根据已确认的订单要求安排产品特定的检验文件。
公司验证以供买家审核
由SGS和TÜV莱茵支持的第三方供应商审核和公司验证服务，可帮助买家审查公司身份、业务运营、供应商概况和整体生产能力。根据订单要求和已确认的产品范围，可提供产品专属的检验报告、材料文件或合规记录。
发布前机器端验证
重现识别维度
For C2040SS Double-Pitch Stainless Steel Chain, record Pitch 25.40 mm, Series C2040SS, Double-pitch stainless construction using consistent datum points. Where wear is visible, measure over several pitches and note whether the chain is relaxed or under load. The objective is a dimension set another engineer can reproduce, not a single convenient measurement.
检查链条路径，而不仅仅是单股链条。
Trace the product through longer-pitch conveyors where lower joint count or carrier spacing suits the machine layout. Mark drive and tail sprockets, guide rails, return tracks, transfer points and the take-up position. Local scuffing or a tight section can indicate alignment or clearance problems that a new chain alone will not correct.
将接口视为加载路径
Review larger pitch geometry, optional rollers, attachments and standard conveyor sprockets. If pans, rods or brackets are fitted, record their hole pattern, offset and repeated spacing. Confirm whether the carrier is rigidly fixed or allowed to articulate, because an over-constrained carrier can force parallel strands out of alignment.
将固定几何图形与可选细节区分开来
Machine pitch, chain centers and carrier mounting points are often fixed by the existing equipment. Material, joint clearance, roller style or attachment manufacturing method may have room for review. This distinction keeps replacement work compatible while allowing the ordered configuration to reflect cooling, transfer and lower-speed bakery conveying with long chain paths.
| 查看 | 为什么这很重要 | 发送或验证哪些内容 |
|---|---|---|
| 已安装几何体 | Verify Pitch 25.40 mm, Series C2040SS, Double-pitch stainless construction against the existing chain or approved machine drawing. | 带尺寸标注的草图以及侧面/端面照片。 |
| 链轮和导轨 | 检查齿形、对齐情况、导向接触情况和滚子密封情况。磨损的配合部件会导致新链条出现拉伸或运转不顺畅的现象。 | 齿数、链轮照片和导轨布局。 |
| 拿起并穿戴 | 记录当前收紧位置和任何调整历史。多节距测量有助于将接头磨损与简单的安装长度问题区分开来。 | 参加旅行和多段式阅读活动。 |
| 环境 | Document cooling, transfer and lower-speed bakery conveying with long chain paths. State normal conditions and short peaks separately where temperature is involved. | 温度/湿度/清洁说明和润滑限制。 |
| 发布检查 | Before ordering, compare the proposed chain with guards, sensors, transfers and the full carrier envelope. The final drawing should control dimensions and options, especially where incorrect sprocket engagement, excessive unsupported span and attachment spacing mismatch is possible. | 已批准图纸修改和所需数量/长度。 |
订购信息
订单计划及商业条款
最小起订量： 评估依据产品类型、生产批次和订单金额。标准目录产品通常采用基于数量的最低生产限额，而大型或高价值产品则可根据项目价值进行评估。
示例： 新客户在所选链条类型和生产工艺合适时，可订购1-5件样品。样品价格和可行性将在生产前确认。
混合订单： 多个型号可以组合在一起，订单金额约为 1,500 美元，但需满足工艺兼容性和包装要求。
极少量： 1-2 件仅供批准的样品、替换或工程案例使用；不接受常规零售订单，特殊处理可能会导致更高的单位成本。
交货时间： 标准件一般需要 10-25 个工作日；定制组件需要 20-45 个工作日；基于项目的设备或复杂包装需要 45-120 个工作日，从图纸和订单确认后开始计算。
贸易条款： EXW、FOB、CIF 和 DAP 是常用的贸易条款。FCA、CFR、CPT、CIP 和 DDP 等条款可根据目的地和运输计划进行协商。
调试检查点
通电前请确认安装几何形状
For C2040SS Double-Pitch Stainless Steel Chain, verify chain centers, sprocket alignment, guide clearance and the mating carrier or attachment with the machine stationary. Turn the system manually where the machine design permits. The chain should enter and leave each sprocket without side forcing, and no attachment, rod or plate should contact a guard or guide through the long-pitch conveyor route.
观察完整的路径，而不仅仅是驱动器端。
Run at a controlled commissioning speed and watch the loaded and return runs. Pay particular attention to roller seating and carrier interval. Listen for a repeating impact and mark the machine position where it occurs. A symptom that repeats at one location is often more useful than a general statement that the chain is noisy or tight.
待实际工艺条件确定后进行复查。
Once the line reaches its normal long conveyor spans, inspect articulation, tracking and take-up position again. Confirm sprocket engagement and guide support. Do not compensate for a local interference by adding excessive chain tension. Record any adjustment so the final maintenance baseline reflects the actual commissioned condition rather than the cold, unloaded setup.
保留维护工作，使其成为可复现的参考。
Store the approved chain drawing, installed length or pitch reference, sprocket tooth count, take-up position and clear photographs of the critical interface. This creates a baseline for later wear checks and gives purchasing a controlled reference when another C2040SS Double-Pitch Stainless Steel Chain strand or compatible replacement is required.
常见问题解答
尺寸是否足以批准更换？
这些是很好的识别起点，但最终检查还需要链轮几何形状、附件布置、负载、材料和机器间隙。
您可以制作自定义附件吗？
如果提供尺寸图、链条几何形状和负载/应用说明，则可以进行自定义附件审查。
询价函里应该附哪些材料？
请提供尺寸、照片、现有图纸（如有）、链条数量或长度、机器类型、温度、清洁环境、负载和所需文件。
