{"id":696,"date":"2026-09-15T06:46:34","date_gmt":"2026-09-15T06:46:34","guid":{"rendered":"https:\/\/bakery-chain.com\/product\/c12s\/"},"modified":"2026-09-15T08:41:20","modified_gmt":"2026-09-15T08:41:20","slug":"c12s","status":"publish","type":"product","link":"https:\/\/bakery-chain.com\/tr\/urun\/c12s\/","title":{"rendered":"C12S Stainless Steel Straight Flat-Top Chain"},"content":{"rendered":"
\n
\n
\n

Industrial Bakery Chain<\/p>\n

C12S Stainless Steel Straight Flat-Top Chain<\/h1>\n

C12S Stainless Steel Straight Flat-Top Chain is presented as a measured-geometry configuration for industrial bakery conveying. Use the dimensional values below for identification and RFQ preparation; final material, heat treatment, clearance, working rating and attachment details are confirmed for the ordered configuration and actual machine duty.<\/p>\n

Zincirleme E\u015fle\u015ftirme \u0130ste\u011fi<\/a>F\u0131r\u0131n zincirlerini ke\u015ffedin<\/a><\/div>\n<\/div>\n<\/div>\n<\/section>\n

<\/p>\n
\n
\n
\n
\"C12S<\/figure>\n<\/div>\n
\n

Configuration Overview<\/h2>\n

C12S Stainless Steel Straight Flat-Top Chain is presented as a measured-geometry configuration for industrial bakery conveying. Use the dimensional values below for identification and RFQ preparation; final material, heat treatment, clearance, working rating and attachment details are confirmed for the ordered configuration and actual machine duty.<\/p>\n

This chain can be reviewed for proofing, baking, cooling, pan handling or transfer service depending on the category and installed interface. A replacement match should preserve pitch, transverse dimensions, sprocket engagement and carrier location.<\/p>\n

Send Dimensions for Review<\/a><\/div>\n<\/div>\n<\/section>\n

\n
\n
\n

How the Chain Is Built<\/h2>\n

A conveyor chain is a sequence of articulated bearings restrained by link plates. The pin and bush establish the bearing joint; a roller or bush engages the sprocket and, where applicable, runs on a track. Bakery versions may add stainless construction, increased clearances, extended pins, hollow pins or attachments for pans and carriers.<\/p>\n

Do not use a photograph alone to approve interchangeability. Two chains can look alike while differing in inside width, pin length, attachment offset or roller diameter. Those differences affect sprocket seating, tracking and machine clearances.<\/p>\n<\/div>\n

\"How<\/figure>\n<\/div>\n<\/section>\n
\n
\n

Dimension Reference<\/h2>\n
\"C12S<\/figure>\n

The drawing\/diagram is shown complete and is not cropped. Use it with the table below for RFQ preparation.<\/p>\n<\/div>\n<\/section>\n

\n
\n

Technical Specifications<\/h2>\n
\n\n\n\n\n\n\n\n
\u00d6zellikler<\/th>\nReferans de\u011feri<\/th>\n<\/tr>\n<\/thead>\n
Pitch 38.10 mm<\/td>\nConfirm on drawing<\/td>\n<\/tr>\n
Series C12S<\/td>\nConfirm on drawing<\/td>\n<\/tr>\n
Straight-running flat-top chain family<\/td>\nConfirm on drawing<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n

Values shown here are identification dimensions associated with this configuration. Confirm the final production drawing before installation, especially where material, clearance, attachment position or performance rating is application-dependent.<\/p>\n<\/div>\n<\/section>\n

\n
\n
\"Bakery<\/figure>\n
\n

Bakery Application Context<\/h2>\n

In bakery equipment, chain duty is defined by more than the product being conveyed. Proofing systems add humidity and long circulation paths; ovens add heat and thermal movement; cooling conveyors may use long transfer routes; pan and tray systems add concentrated carrier loads; packaging areas often require stable, clean transfer.<\/p>\n

Record the machine zone, product carrier, chain speed, load per carrier and cleaning routine. If the chain passes through a transition between zones, include that transition in the RFQ because temperature and contamination can change along the route.<\/p>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Selection and Customization<\/h2>\n
\n
\n

Geometry match<\/h3>\n

Confirm pitch, inside width, roller\/bush diameter, pin diameter, plate height and overall width.<\/p>\n<\/article>\n

\n

Attachment match<\/h3>\n

Define mounting holes, bend direction, offset, cross-rod size and repeated spacing.<\/p>\n<\/article>\n

\n

Material choice<\/h3>\n

State moisture, washdown, cleaning chemistry and temperature; material is confirmed against those conditions.<\/p>\n<\/article>\n

\n

System check<\/h3>\n

Inspect sprockets, guides, take-up and alignment so a new chain is not installed into a worn or misaligned system.<\/p>\n<\/article>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Installation, Inspection and Maintenance<\/h2>\n

Before installation, lock out the machine and inspect the sprockets and guides. Worn or hooked teeth can prevent smooth roller seating and accelerate wear in a new chain. Confirm that shafts are aligned, the take-up has usable travel and parallel strands remain synchronized where the conveyor uses more than one chain.<\/p>\n

During commissioning, watch the chain through at least one complete circuit. Look for tight joints, side rubbing, carrier interference and unusual noise at sprocket entry or exit. After the initial running period, recheck tension or take-up position according to the machine maker’s practice.<\/p>\n

For maintenance planning, our bakery chain maintenance guide<\/a> covers inspection points, while the Paslanmaz \u00c7elik D\u00fcz \u00dcst Zincirler<\/a> page compares related configurations.<\/p>\n<\/div>\n<\/section>\n

\n
\n

Manufacturing and Inspection<\/h2>\n
\"Bakery<\/figure>\n

Dimensional inspection should verify the characteristics that control interchangeability: pitch consistency, transverse width, pin projection, roller or bush size and attachment location. For custom configurations, inspection should also verify the carrier hole pattern and attachment interval against the approved drawing. Product-specific inspection documents can be arranged according to the confirmed order requirements.<\/p>\n

\n

Al\u0131c\u0131 \u0130ncelemesi i\u00e7in \u015eirket Do\u011frulama<\/h3>\n

SGS ve T\u00dcV Rheinland taraf\u0131ndan desteklenen \u00fc\u00e7\u00fcnc\u00fc taraf tedarik\u00e7i denetimi ve \u015firket do\u011frulama hizmetleri, al\u0131c\u0131lar\u0131n \u015firket kimli\u011fini, i\u015f operasyonlar\u0131n\u0131, tedarik\u00e7i profilini ve genel \u00fcretim kapasitesini incelemelerine yard\u0131mc\u0131 olmak i\u00e7in sunulmaktad\u0131r. Sipari\u015f gereksinimlerine ve onaylanm\u0131\u015f \u00fcr\u00fcn kapsam\u0131na g\u00f6re \u00fcr\u00fcne \u00f6zel denetim raporlar\u0131, malzeme belgeleri veya uygunluk kay\u0131tlar\u0131 sa\u011flanabilir.<\/p>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Machine-Side Verification Before Release<\/h2>\n
\n
\n

Reproduce the identification dimensions<\/h3>\n

For C12S Stainless Steel Straight Flat-Top Chain, record Pitch 38.10 mm, Series C12S, Straight-running flat-top chain family using consistent datum points. Where wear is visible, measure over several pitches and note whether the chain is relaxed or under load. The objective is a dimension set another engineer can reproduce, not a single convenient measurement.<\/p>\n<\/article>\n

\n

Check the chain route, not only the strand<\/h3>\n

Trace the product through straight-running product transfer and packaging in bakery downstream handling. Mark drive and tail sprockets, guide rails, return tracks, transfer points and the take-up position. Local scuffing or a tight section can indicate alignment or clearance problems that a new chain alone will not correct.<\/p>\n<\/article>\n

\n

Treat the interface as a load path<\/h3>\n

Review flat top plates, wear strips, guides and transfer points. If pans, rods or brackets are fitted, record their hole pattern, offset and repeated spacing. Confirm whether the carrier is rigidly fixed or allowed to articulate, because an over-constrained carrier can force parallel strands out of alignment.<\/p>\n<\/article>\n

\n

Separate fixed geometry from selectable details<\/h3>\n

Machine pitch, chain centers and carrier mounting points are often fixed by the existing equipment. Material, joint clearance, roller style or attachment manufacturing method may have room for review. This distinction keeps replacement work compatible while allowing the ordered configuration to reflect clean transfer zones with frequent contact between the conveying surface and packaged or finished product.<\/p>\n<\/article>\n<\/div>\n

\n\n\n\n\n\n\n\n\n\n
Check<\/th>\nWhy it matters<\/th>\nWhat to send or verify<\/th>\n<\/tr>\n<\/thead>\n
Installed geometry<\/td>\nVerify Pitch 38.10 mm, Series C12S, Straight-running flat-top chain family against the existing chain or approved machine drawing.<\/td>\nDimensioned sketch plus side\/end photos.<\/td>\n<\/tr>\n
Sprockets and guides<\/td>\nCheck tooth profile, alignment, guide contact and roller seating. Worn mating parts can make a new chain appear to stretch or run rough.<\/td>\nTooth count, sprocket photos and guide layout.<\/td>\n<\/tr>\n
Take-up and wear<\/td>\nRecord current take-up position and any adjustment history. Multi-pitch measurement helps separate joint wear from a simple installation-length issue.<\/td>\nTake-up travel and multi-pitch reading.<\/td>\n<\/tr>\n
Environment<\/td>\nDocument clean transfer zones with frequent contact between the conveying surface and packaged or finished product. State normal conditions and short peaks separately where temperature is involved.<\/td>\nTemperature\/humidity\/cleaning description and lubrication constraints.<\/td>\n<\/tr>\n
Release check<\/td>\nBefore ordering, compare the proposed chain with guards, sensors, transfers and the full carrier envelope. The final drawing should control dimensions and options, especially where plate scuffing, unstable transfer and guide wear caused by poor alignment is possible.<\/td>\nApproved drawing revision and requested quantity\/length.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n

Ordering Information<\/h2>\n
\n

Sipari\u015f Planlamas\u0131 ve Ticari \u015eartlar<\/h3>\n
\n

Minimum Sipari\u015f Miktar\u0131:<\/strong> \u00dcr\u00fcn t\u00fcr\u00fc, \u00fcretim partisi ve sipari\u015f de\u011feri dikkate al\u0131narak de\u011ferlendirilir. Standart katalog \u00fcr\u00fcnleri genellikle miktar bazl\u0131 minimum \u00fcretim limitlerine tabidir, b\u00fcy\u00fck veya y\u00fcksek de\u011ferli \u00fcr\u00fcnler ise proje de\u011ferine g\u00f6re incelenebilir.<\/p>\n

\u00d6rnekler:<\/strong> Yeni m\u00fc\u015fteriler, se\u00e7ilen zincir tipi ve \u00fcretim y\u00f6ntemi uygun oldu\u011funda 1-5 adet sipari\u015f verebilirler. \u00dcretim \u00f6ncesinde numune fiyatland\u0131rmas\u0131 ve uygulanabilirli\u011fi teyit edilir.<\/p>\n

Kar\u0131\u015f\u0131k sipari\u015fler:<\/strong> \u00dcretim s\u00fcreci uyumlulu\u011fu ve paketleme gereksinimlerine ba\u011fl\u0131 olarak, yakla\u015f\u0131k 1.500 ABD dolar\u0131 tutar\u0131ndaki sipari\u015f de\u011ferine ula\u015fmak i\u00e7in birden fazla model birle\u015ftirilebilir.<\/p>\n

\u00c7ok k\u00fc\u00e7\u00fck miktarlar:<\/strong> 1-2 adetlik sipari\u015fler yaln\u0131zca onayl\u0131 numune, yedek par\u00e7a veya m\u00fchendislik durumlar\u0131 i\u00e7in de\u011ferlendirilir; rutin perakende sipari\u015fleri kabul edilmez ve \u00f6zel i\u015flem, birim maliyetinin artmas\u0131na neden olabilir.<\/p>\n

Kur\u015fun zaman\u0131:<\/strong> Standart \u00fcr\u00fcnler i\u00e7in genellikle 10-25 i\u015f g\u00fcn\u00fc; \u00f6zel par\u00e7alar i\u00e7in 20-45 i\u015f g\u00fcn\u00fc; proje bazl\u0131 ekipman veya karma\u015f\u0131k paketler i\u00e7in ise \u00e7izim ve sipari\u015f onay\u0131ndan sonra 45-120 i\u015f g\u00fcn\u00fc s\u00fcre ge\u00e7erlidir.<\/p>\n

Ticaret \u015fartlar\u0131:<\/strong> EXW, FOB, CIF ve DAP genellikle desteklenmektedir. Var\u0131\u015f noktas\u0131 ve sevkiyat plan\u0131 i\u00e7in FCA, CFR, CPT, CIP ve DDP g\u00f6r\u00fc\u015f\u00fclebilir.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Commissioning Checkpoints<\/h2>\n
\n
01 \u2014 Static check<\/strong><\/p>\n

Confirm the installed geometry before power-up<\/h3>\n

For C12S Stainless Steel Straight Flat-Top Chain, verify chain centers, sprocket alignment, guide clearance and the mating carrier or attachment with the machine stationary. Turn the system manually where the machine design permits. The chain should enter and leave each sprocket without side forcing, and no attachment, rod or plate should contact a guard or guide through the transfer route.<\/p>\n<\/article>\n

02 \u2014 First circuit<\/strong><\/p>\n

Observe one complete path, not only the drive end<\/h3>\n

Run at a controlled commissioning speed and watch the loaded and return runs. Pay particular attention to top-plate tracking and transfer stability. Listen for a repeating impact and mark the machine position where it occurs. A symptom that repeats at one location is often more useful than a general statement that the chain is noisy or tight.<\/p>\n<\/article>\n

03 \u2014 Duty check<\/strong><\/p>\n

Recheck after the real process condition is established<\/h3>\n

Once the line reaches its normal downstream handling, inspect articulation, tracking and take-up position again. Confirm wear-strip, guide and transfer-gap alignment. Do not compensate for a local interference by adding excessive chain tension. Record any adjustment so the final maintenance baseline reflects the actual commissioned condition rather than the cold, unloaded setup.<\/p>\n<\/article>\n

04 \u2014 Baseline record<\/strong><\/p>\n

Leave maintenance a reproducible reference<\/h3>\n

Store the approved chain drawing, installed length or pitch reference, sprocket tooth count, take-up position and clear photographs of the critical interface. This creates a baseline for later wear checks and gives purchasing a controlled reference when another C12S Stainless Steel Straight Flat-Top Chain strand or compatible replacement is required.<\/p>\n<\/article>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Frequently Asked Questions<\/h2>\n
\n
\nAre the dimensions enough to approve a replacement?<\/summary>\n

They are a strong identification start, but the final check also needs sprocket geometry, attachment arrangement, duty, material and machine clearances.<\/p>\n<\/details>\n

\nCan you make a custom attachment?<\/summary>\n

Custom attachment review is possible when a dimensioned drawing, chain geometry and load\/application description are provided.<\/p>\n<\/details>\n

\nWhat should I send with an RFQ?<\/summary>\n

Send dimensions, photos, existing drawing if available, chain quantity or length, machine type, temperature, cleaning environment, load and requested documentation.<\/p>\n<\/details>\n<\/div>\n<\/div>\n<\/section>\n

<\/main><\/p>","protected":false},"excerpt":{"rendered":"

Industrial Bakery Chain C12S Stainless Steel Straight Flat-Top Chain C12S Stainless Steel Straight Flat-Top Chain is presented as a measured-geometry configuration for industrial bakery conveying. Use the dimensional values below for identification and RFQ preparation; final material, heat treatment, clearance, working rating and attachment details are confirmed for the ordered configuration and actual machine duty. […]<\/p>","protected":false},"featured_media":542,"comment_status":"open","ping_status":"closed","template":"","meta":[],"product_cat":[1715],"product_tag":[],"class_list":["post-696","product","type-product","status-publish","has-post-thumbnail","product_cat-flat-top-bakery-chains","first","instock","shipping-taxable","product-type-simple"],"_links":{"self":[{"href":"https:\/\/bakery-chain.com\/tr\/wp-json\/wp\/v2\/product\/696","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/bakery-chain.com\/tr\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/bakery-chain.com\/tr\/wp-json\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/bakery-chain.com\/tr\/wp-json\/wp\/v2\/comments?post=696"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/bakery-chain.com\/tr\/wp-json\/wp\/v2\/media\/542"}],"wp:attachment":[{"href":"https:\/\/bakery-chain.com\/tr\/wp-json\/wp\/v2\/media?parent=696"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/bakery-chain.com\/tr\/wp-json\/wp\/v2\/product_cat?post=696"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/bakery-chain.com\/tr\/wp-json\/wp\/v2\/product_tag?post=696"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}