{"id":694,"date":"2026-09-15T06:46:21","date_gmt":"2026-09-15T06:46:21","guid":{"rendered":"https:\/\/bakery-chain.com\/product\/08bhpss\/"},"modified":"2026-09-15T08:41:17","modified_gmt":"2026-09-15T08:41:17","slug":"08bhpss","status":"publish","type":"product","link":"https:\/\/bakery-chain.com\/id\/produk\/08bhpss\/","title":{"rendered":"08BHPSS Stainless Steel Hollow-Pin Chain"},"content":{"rendered":"
\n
\n
\n

Industrial Bakery Chain<\/p>\n

08BHPSS Stainless Steel Hollow-Pin Chain<\/h1>\n

08BHPSS Stainless Steel Hollow-Pin Chain is presented as a measured-geometry configuration for industrial bakery conveying. Use the dimensional values below for identification and RFQ preparation; final material, heat treatment, clearance, working rating and attachment details are confirmed for the ordered configuration and actual machine duty.<\/p>\n

Minta Pertandingan Berantai<\/a>Jelajahi Jaringan Toko Roti<\/a><\/div>\n<\/div>\n<\/div>\n<\/section>\n

<\/p>\n
\n
\n
\n
\"08BHPSS<\/figure>\n<\/div>\n
\n

Configuration Overview<\/h2>\n

08BHPSS Stainless Steel Hollow-Pin Chain is presented as a measured-geometry configuration for industrial bakery conveying. Use the dimensional values below for identification and RFQ preparation; final material, heat treatment, clearance, working rating and attachment details are confirmed for the ordered configuration and actual machine duty.<\/p>\n

This chain can be reviewed for proofing, baking, cooling, pan handling or transfer service depending on the category and installed interface. A replacement match should preserve pitch, transverse dimensions, sprocket engagement and carrier location.<\/p>\n

Send Dimensions for Review<\/a><\/div>\n<\/div>\n<\/section>\n

\n
\n
\n

How the Chain Is Built<\/h2>\n

A conveyor chain is a sequence of articulated bearings restrained by link plates. The pin and bush establish the bearing joint; a roller or bush engages the sprocket and, where applicable, runs on a track. Bakery versions may add stainless construction, increased clearances, extended pins, hollow pins or attachments for pans and carriers.<\/p>\n

Do not use a photograph alone to approve interchangeability. Two chains can look alike while differing in inside width, pin length, attachment offset or roller diameter. Those differences affect sprocket seating, tracking and machine clearances.<\/p>\n<\/div>\n

\"How<\/figure>\n<\/div>\n<\/section>\n
\n
\n

Dimension Reference<\/h2>\n
\"08BHPSS<\/figure>\n

The drawing\/diagram is shown complete and is not cropped. Use it with the table below for RFQ preparation.<\/p>\n<\/div>\n<\/section>\n

\n
\n

Technical Specifications<\/h2>\n
\n\n\n\n\n\n\n\n
Spesifikasi<\/th>\nNilai referensi<\/th>\n<\/tr>\n<\/thead>\n
Pitch 12.70 mm<\/td>\nConfirm on drawing<\/td>\n<\/tr>\n
Series 08BHPSS<\/td>\nConfirm on drawing<\/td>\n<\/tr>\n
Hollow-pin construction for cross rods \/ fixtures<\/td>\nConfirm on drawing<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n

Values shown here are identification dimensions associated with this configuration. Confirm the final production drawing before installation, especially where material, clearance, attachment position or performance rating is application-dependent.<\/p>\n<\/div>\n<\/section>\n

\n
\n
\"Bakery<\/figure>\n
\n

Bakery Application Context<\/h2>\n

In bakery equipment, chain duty is defined by more than the product being conveyed. Proofing systems add humidity and long circulation paths; ovens add heat and thermal movement; cooling conveyors may use long transfer routes; pan and tray systems add concentrated carrier loads; packaging areas often require stable, clean transfer.<\/p>\n

Record the machine zone, product carrier, chain speed, load per carrier and cleaning routine. If the chain passes through a transition between zones, include that transition in the RFQ because temperature and contamination can change along the route.<\/p>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Selection and Customization<\/h2>\n
\n
\n

Geometry match<\/h3>\n

Confirm pitch, inside width, roller\/bush diameter, pin diameter, plate height and overall width.<\/p>\n<\/article>\n

\n

Attachment match<\/h3>\n

Define mounting holes, bend direction, offset, cross-rod size and repeated spacing.<\/p>\n<\/article>\n

\n

Material choice<\/h3>\n

State moisture, washdown, cleaning chemistry and temperature; material is confirmed against those conditions.<\/p>\n<\/article>\n

\n

System check<\/h3>\n

Inspect sprockets, guides, take-up and alignment so a new chain is not installed into a worn or misaligned system.<\/p>\n<\/article>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Installation, Inspection and Maintenance<\/h2>\n

Before installation, lock out the machine and inspect the sprockets and guides. Worn or hooked teeth can prevent smooth roller seating and accelerate wear in a new chain. Confirm that shafts are aligned, the take-up has usable travel and parallel strands remain synchronized where the conveyor uses more than one chain.<\/p>\n

During commissioning, watch the chain through at least one complete circuit. Look for tight joints, side rubbing, carrier interference and unusual noise at sprocket entry or exit. After the initial running period, recheck tension or take-up position according to the machine maker’s practice.<\/p>\n

For maintenance planning, our bakery chain maintenance guide<\/a> covers inspection points, while the Rantai Toko Roti Hollow Pin<\/a> page compares related configurations.<\/p>\n<\/div>\n<\/section>\n

\n
\n

Manufacturing and Inspection<\/h2>\n
\"Bakery<\/figure>\n

Dimensional inspection should verify the characteristics that control interchangeability: pitch consistency, transverse width, pin projection, roller or bush size and attachment location. For custom configurations, inspection should also verify the carrier hole pattern and attachment interval against the approved drawing. Product-specific inspection documents can be arranged according to the confirmed order requirements.<\/p>\n

\n

Verifikasi Perusahaan untuk Tinjauan Pembeli<\/h3>\n

Audit pemasok pihak ketiga dan verifikasi perusahaan yang didukung oleh SGS dan T\u00dcV Rheinland tersedia untuk membantu pembeli meninjau identitas perusahaan, operasional bisnis, profil pemasok, dan kemampuan manufaktur secara umum. Laporan inspeksi khusus produk, dokumen material, atau catatan kepatuhan dapat diberikan sesuai dengan persyaratan pesanan dan ruang lingkup produk yang telah dikonfirmasi.<\/p>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Machine-Side Verification Before Release<\/h2>\n
\n
\n

Reproduce the identification dimensions<\/h3>\n

For 08BHPSS Stainless Steel Hollow-Pin Chain, record Pitch 12.70 mm, Series 08BHPSS, Hollow-pin construction for cross rods \/ fixtures using consistent datum points. Where wear is visible, measure over several pitches and note whether the chain is relaxed or under load. The objective is a dimension set another engineer can reproduce, not a single convenient measurement.<\/p>\n<\/article>\n

\n

Check the chain route, not only the strand<\/h3>\n

Trace the product through conveyors using cross rods, shafts or removable carrier fixtures through the chain. Mark drive and tail sprockets, guide rails, return tracks, transfer points and the take-up position. Local scuffing or a tight section can indicate alignment or clearance problems that a new chain alone will not correct.<\/p>\n<\/article>\n

\n

Treat the interface as a load path<\/h3>\n

Review hollow pins, cross rods, retaining hardware and parallel chain strands. If pans, rods or brackets are fitted, record their hole pattern, offset and repeated spacing. Confirm whether the carrier is rigidly fixed or allowed to articulate, because an over-constrained carrier can force parallel strands out of alignment.<\/p>\n<\/article>\n

\n

Separate fixed geometry from selectable details<\/h3>\n

Machine pitch, chain centers and carrier mounting points are often fixed by the existing equipment. Material, joint clearance, roller style or attachment manufacturing method may have room for review. This distinction keeps replacement work compatible while allowing the ordered configuration to reflect proofing, cooling and transfer duties where carrier change or cleaning access matters.<\/p>\n<\/article>\n<\/div>\n

\n\n\n\n\n\n\n\n\n\n
Memeriksa<\/th>\nMengapa ini penting<\/th>\nApa yang perlu dikirim atau diverifikasi<\/th>\n<\/tr>\n<\/thead>\n
Installed geometry<\/td>\nVerify Pitch 12.70 mm, Series 08BHPSS, Hollow-pin construction for cross rods \/ fixtures against the existing chain or approved machine drawing.<\/td>\nDimensioned sketch plus side\/end photos.<\/td>\n<\/tr>\n
Sprockets and guides<\/td>\nCheck tooth profile, alignment, guide contact and roller seating. Worn mating parts can make a new chain appear to stretch or run rough.<\/td>\nTooth count, sprocket photos and guide layout.<\/td>\n<\/tr>\n
Take-up and wear<\/td>\nRecord current take-up position and any adjustment history. Multi-pitch measurement helps separate joint wear from a simple installation-length issue.<\/td>\nTake-up travel and multi-pitch reading.<\/td>\n<\/tr>\n
Lingkungan<\/td>\nDocument proofing, cooling and transfer duties where carrier change or cleaning access matters. State normal conditions and short peaks separately where temperature is involved.<\/td>\nTemperature\/humidity\/cleaning description and lubrication constraints.<\/td>\n<\/tr>\n
Release check<\/td>\nBefore ordering, compare the proposed chain with guards, sensors, transfers and the full carrier envelope. The final drawing should control dimensions and options, especially where cross-rod binding, unequal strand loading and loss of articulation from over-tight fixtures is possible.<\/td>\nApproved drawing revision and requested quantity\/length.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n

Ordering Information<\/h2>\n
\n

Perencanaan Pesanan & Persyaratan Komersial<\/h3>\n
\n

Jumlah Pesanan Minimum (MOQ):<\/strong> Dievaluasi berdasarkan jenis produk, batch produksi, dan nilai pesanan. Item katalog standar umumnya menggunakan minimum produksi berdasarkan kuantitas, sedangkan item besar atau bernilai tinggi dapat ditinjau berdasarkan nilai proyek.<\/p>\n

Contoh:<\/strong> Pelanggan baru dapat memesan 1\u20135 buah jika jenis rantai dan jalur produksi yang dipilih sesuai. Harga sampel dan kelayakan akan dikonfirmasi sebelum produksi.<\/p>\n

Pesanan campur:<\/strong> Beberapa model dapat digabungkan untuk mencapai nilai pesanan sekitar USD 1.500, tergantung pada kompatibilitas proses dan persyaratan pengemasan.<\/p>\n

Jumlah yang sangat kecil:<\/strong> 1\u20132 buah hanya dipertimbangkan untuk sampel yang disetujui, penggantian, atau kasus rekayasa; pesanan ritel rutin tidak diterima, dan penanganan khusus dapat mengakibatkan biaya per unit yang lebih tinggi.<\/p>\n

Waktu tunggu:<\/strong> Barang standar biasanya membutuhkan waktu 10\u201325 hari kerja; komponen khusus 20\u201345 hari; peralatan berbasis proyek atau paket kompleks 45\u2013120 hari, setelah konfirmasi gambar dan pesanan.<\/p>\n

Syarat perdagangan:<\/strong> EXW, FOB, CIF, dan DAP umumnya didukung. FCA, CFR, CPT, CIP, dan DDP dapat didiskusikan tergantung tujuan dan rencana pengiriman.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Commissioning Checkpoints<\/h2>\n
\n
01 \u2014 Static check<\/strong><\/p>\n

Confirm the installed geometry before power-up<\/h3>\n

For 08BHPSS Stainless Steel Hollow-Pin Chain, verify chain centers, sprocket alignment, guide clearance and the mating carrier or attachment with the machine stationary. Turn the system manually where the machine design permits. The chain should enter and leave each sprocket without side forcing, and no attachment, rod or plate should contact a guard or guide through the cross-rod route.<\/p>\n<\/article>\n

02 \u2014 First circuit<\/strong><\/p>\n

Observe one complete path, not only the drive end<\/h3>\n

Run at a controlled commissioning speed and watch the loaded and return runs. Pay particular attention to rod retention and free articulation. Listen for a repeating impact and mark the machine position where it occurs. A symptom that repeats at one location is often more useful than a general statement that the chain is noisy or tight.<\/p>\n<\/article>\n

03 \u2014 Duty check<\/strong><\/p>\n

Recheck after the real process condition is established<\/h3>\n

Once the line reaches its normal carrier loading and cleaning, inspect articulation, tracking and take-up position again. Confirm cross-rod fit and parallel-strand synchronization. Do not compensate for a local interference by adding excessive chain tension. Record any adjustment so the final maintenance baseline reflects the actual commissioned condition rather than the cold, unloaded setup.<\/p>\n<\/article>\n

04 \u2014 Baseline record<\/strong><\/p>\n

Leave maintenance a reproducible reference<\/h3>\n

Store the approved chain drawing, installed length or pitch reference, sprocket tooth count, take-up position and clear photographs of the critical interface. This creates a baseline for later wear checks and gives purchasing a controlled reference when another 08BHPSS Stainless Steel Hollow-Pin Chain strand or compatible replacement is required.<\/p>\n<\/article>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Pertanyaan yang Sering Diajukan<\/h2>\n
\n
\nAre the dimensions enough to approve a replacement?<\/summary>\n

They are a strong identification start, but the final check also needs sprocket geometry, attachment arrangement, duty, material and machine clearances.<\/p>\n<\/details>\n

\nCan you make a custom attachment?<\/summary>\n

Custom attachment review is possible when a dimensioned drawing, chain geometry and load\/application description are provided.<\/p>\n<\/details>\n

\nWhat should I send with an RFQ?<\/summary>\n

Send dimensions, photos, existing drawing if available, chain quantity or length, machine type, temperature, cleaning environment, load and requested documentation.<\/p>\n<\/details>\n<\/div>\n<\/div>\n<\/section>\n

<\/main><\/p>","protected":false},"excerpt":{"rendered":"

Industrial Bakery Chain 08BHPSS Stainless Steel Hollow-Pin Chain 08BHPSS Stainless Steel Hollow-Pin Chain is presented as a measured-geometry configuration for industrial bakery conveying. Use the dimensional values below for identification and RFQ preparation; final material, heat treatment, clearance, working rating and attachment details are confirmed for the ordered configuration and actual machine duty. Request a […]<\/p>","protected":false},"featured_media":546,"comment_status":"open","ping_status":"closed","template":"","meta":[],"product_cat":[1713],"product_tag":[],"class_list":["post-694","product","type-product","status-publish","has-post-thumbnail","product_cat-hollow-pin-bakery-chains","first","instock","shipping-taxable","product-type-simple"],"_links":{"self":[{"href":"https:\/\/bakery-chain.com\/id\/wp-json\/wp\/v2\/product\/694","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/bakery-chain.com\/id\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/bakery-chain.com\/id\/wp-json\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/bakery-chain.com\/id\/wp-json\/wp\/v2\/comments?post=694"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/bakery-chain.com\/id\/wp-json\/wp\/v2\/media\/546"}],"wp:attachment":[{"href":"https:\/\/bakery-chain.com\/id\/wp-json\/wp\/v2\/media?parent=694"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/bakery-chain.com\/id\/wp-json\/wp\/v2\/product_cat?post=694"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/bakery-chain.com\/id\/wp-json\/wp\/v2\/product_tag?post=694"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}